Sigma 10m9 instructions

[projectile]

Hi guys bought this machine second hand a few weeks back. As it is very cumbersome to move for one person i strip down the out feed table which then makes it a doddle to move around jobs. There are x2 13mm nuts which hold the out feed table in place ,which are attached to two off set pins, which raise/lower and move the out feed table in/out.
Have trawled the net for instructions/manual but have come up with a blank . Just want to know how to set it up correctly each time when putting it back together. If no joy here i will ring Sigma. Cheers

 

[Time's Ran Out]

They are not very popular on here but I'am sure someone will be along to help!
Me I'am a Kenny Rogers fan!

 

[Qwerty]

If nobody on here responds just drop me a PM and I will forward you the rep's details

 

[LM]

Hi guys bought this machine second hand a few weeks back. As it is very cumbersome to move for one person i strip down the out feed table which then makes it a doddle to move around jobs. There are x2 13mm nuts which hold the out feed table in place ,which are attached to two off set pins, which raise/lower and move the out feed table in/out.
Have trawled the net for instructions/manual but have come up with a blank . Just want to know how to set it up correctly each time when putting it back together. If no joy here i will ring Sigma. Cheers

This is a simple procedure,
1: erect the stand in the desired location bearing in mind direction and working room around the machine
2: place the main body of the wet saw on the stand then insert the sliding bed into position by guiding the pins on each side into their locating holes, fix the washers and slightly tighten handles
3: raise the sliding table up to its level position and hold in place as you tighten the handles
4: insert the under side splash guard into its slots
5: insert the water tray and fill to the water mark and your good to go. Obviously reverse the process to disassemble

 

[Italy]

This is a simple procedure,
1: erect the stand in the desired location bearing in mind direction and working room around the machine
2: place the main body of the wet saw on the stand then insert the sliding bed into position by guiding the pins on each side into their locating holes, fix the washers and slightly tighten handles
3: raise the sliding table up to its level position and hold in place as you tighten the handles
4: insert the under side splash guard into its slots
5: insert the water tray and fill to the water mark and your good to go. Obviously reverse the process to disassemble

Master lee

 

[projectile]

This is a simple procedure,
1: erect the stand in the desired location bearing in mind direction and working room around the machine
2: place the main body of the wet saw on the stand then insert the sliding bed into position by guiding the pins on each side into their locating holes, fix the washers and slightly tighten handles
3: raise the sliding table up to its level position and hold in place as you tighten the handles
4: insert the under side splash guard into its slots
5: insert the water tray and fill to the water mark and your good to go. Obviously reverse the process to disassemble

Hi Lee Mac, item 3 raise the sliding table up that's great but if the out feed table is not level with the main body you then have to mess with the two off set pins to get it level, or am I missing something here. The reason for the initial post was when you turn the tile over to make a nic to stop it breaking when you do the full cut, the nic and full cut are about 1 1/2 mm out. So I moved the fence to accommodate this difference but it makes no difference. That's why I wanted to know about setting up the out feed table thinking the difference with the cut may be to do with the off set pins. Hope you can help. Cheers

 

[Dave]

You should find all spec sheets on the Sigma Italia website.

If you are using the fence for cutting as you describe , then if its running out of true , then adjust the fence stop nut thread..

 

[Italy]

You should find all spec sheets on the Sigma Italia website.

If you are using the fence for cutting as you describe , then if its running out of true , then adjust the fence stop nut thread..

You should find all spec sheets on the Sigma Italia website.
I have tried today, but I have not found

 

[projectile]

You should find all spec sheets on the Sigma Italia website.
I have tried today, but I have not found

Tradetiler tried too with no joy.

 

[projectile]

You should find all spec sheets on the Sigma Italia website.

If you are using the fence for cutting as you describe , then if its running out of true , then adjust the fence stop nut thread..

Hi Dave that's what I did but confusingly if there is such a word it made do difference ??????