Bathroom tiling help.

[Cabnero]

Hi again guys. I'm on day 2 if tiling my mum's bathroom thanks to you all with help prep and layout which I'm happy with. However there is a couple of problems which I should have checked and asked about. Firstly the walls have been dot and dabed by the builder and screwed and plugged. However I've only today noticed slight movement in the wall where it meets the window wall. I know I should have double checked but it is half tiled now. There is a dab unscrewed which I will plug and screw but don't think it's going to make a difference. Can in do anything else. I.e use a long screw. Any suggestions would be welcome. Can I check re the hardie. It's down and screwed with turbo golds 4 x25 as suggested. Some of the heads are slightly proud of the board. Is this OK or will I be ok to screw them again. Thanks again fellas.

 

[White Room]

Hi again guys. I'm on day 2 if tiling my mum's bathroom thanks to you all with help prep and layout which I'm happy with. However there is a couple of problems which I should have checked and asked about. Firstly the walls have been dot and dabed by the builder and screwed and plugged. However I've only today noticed slight movement in the wall where it meets the window wall. I know I should have double checked but it is half tiled now. There is a dab unscrewed which I will plug and screw but don't think it's going to make a difference. Can in do anything else. I.e use a long screw. Any suggestions would be welcome. Can I check re the hardie. It's down and screwed with turbo golds 4 x25 as suggested. Some of the heads are slightly proud of the board. Is this OK or will I be ok to screw them again. Thanks again fellas.

Dot and dabbed with plasterboard ?

 

[Cabnero]

Hi whitebeam. Yeah 12.5 plasterboard

 

[White Room]

What was the existing substrate they were fixed to ?

 

[Cabnero]

Sorry, it was sand and cement render. Very solid.

 

[White Room]

Quoted;There is a dab unscrewed which I will plug and screw but don't think it's going to make a difference. Can in do anything else.

Has the dri wall adhesive become unstuck ?

 

[Cabnero]

No the adhesive is pretty solid. By tapping the board there is a solid sound which I assume is a dab. I don't think screwing this will make a difference to the movement though. I think there is too big a gap between the dabs. This is the only area of movement there is.

 

[Cris]

Drill board next to loose dab with 15mm hole saw, remove and fill all round inside of hole with expanding foam. I've done it in past and worked a treat

 

[Cabnero]

Thanks Cris. Dint you have to be careful how much you put in our it will form a belly? I presume I need to tillage the piece of plastboard?

 

[White Room]

If boards of 8x4 was used the dabs there should be 3 vertical dabs fairly close, horizontal about 400mm....does that sound right when tapping the boards ?

 

[Cabnero]

Yeah roughly. I think there is a missing dab horizontally between the one I've mentioned and the area of movement. Trouble is not sure about the quality of the builders work so can't day he'd have done this "by the book". I can call him tomorrow to find out.

 

[White Room]

Your best bet to start with is as you say plug and screw in the area where it's loose but only where the dabs are...

 

[Cris]

Don't flood it ,just enough to bond the board and itl be fine

 

[Cris]

Any large voids behind the board and u can use same process, just don't use an excess of foam

 

[Cabnero]

Thank you guys. I'll try that. Do I need to replace the piece of pb that I cut out our tile across.

 

[White Room]

Thank you guys. I'll try that. Do I need to replace the piece of pb that I cut out our tile across.

That make no sense as in reading and understanding.

 

[Cabnero]

Sorry misread criss' post 15 mm hole saw. I'd quickly read it as cut a piece out.

 

[Mike ramsdale]

Just cut half a metre square round the loose board and dab new piece on.

 

[Cabnero]

Thanks Mark. Just saw your thread. I did a combo of what criss and whitebeam said but your suggestion did cross my mind! Thanks again.