You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
tile adhesive
Porcelain tiles or ceramic tiles are porcelain or ceramic tiles commonly used to cover floors and walls, with a water absorption rate of less than 0.5 percent. The clay used to build porcelain tiles is generally denser. They can either be glazed or unglazed. Porcelain tiles are one type of vitrified tiles and are sometimes referred to as porcelain vitrified tiles.
Historically, porcelain was not the usual material for tiles, which were much more often made of earthenware (terracotta) or stoneware. The first porcelain tiles were made in China, for example in the 15th-century Porcelain Tower of Nanjing (now largely destroyed). Here the tiles were used for walls, which long remained typical. In Europe, a few rooms were made in palaces of porcelain plaques, often with forms in high relief. These were made by Capodimonte porcelain and Real Fábrica del Buen Retiro among others.
Although porcelain has now been widely used for making tiles for many years, modern production methods and quantities have made porcelain tiles available for the average householder in recent years.
I've got an AKW Tuff form shower tray with a waste that is 10mm above the tray when fully screwed in. The Tiler laid my 5mm hex mosaic tiles on a 2mm bed, so obvs wasn't going to drain.
I took them back up and spoke to AKW, who recommended I put down a 3mm bed adhesive, let it go off and then...
Hi guys,
I've had a bit of an issue on a job I've been doing recently. We finished tiling on Friday using a new adhesive (python rapid and standard adhesive) and also a new grout that I've not used before (Validus)
Basically I came in to grout on Saturday midday, so majority of the adhesive...
Hi, so I’m relatively new to tiling. I’ve got a job where the walls aren’t 100% flat but not the worst. I’ve sealed the old plaster with a primer. Am I ok to dot and dab the tiles, I don’t mean 5 dots with 20% coverage, the dots I’d put on would get a minimum coverage of around a 70% adhesive...
The saga of my hollow floor 50sqm continues. All tiles now lifted but there is adhesive around the edges of most tiles (800x800) and a small amount on the back. Whats the best method of cleaning these tiles ip ready for relaying? The tiles were not grouted and the adhesive residue is around the...
I recently got several loose/hollow tiles rebonded on my bathroom floor. Having left with several drill holes and cracked grout, I hired someone to do the repair and replace all the cracked grout with new grout. This contractor said he was going to use epoxy grout for the job and when I...
Further to my other post re our hollow tiles issue It looks like our tiler has dot and dabbed most of our floor to accommodate tiling 800x800 porcelain over an uneven floor.
The gap from defrac membrane to the underside of the tiles in question is around 20mm. The membrane sits directly on our...
I'm tiling over tiles and I want to extend them a little way beyond where the old ones stop. Can I apply the adhesive an extra 6mm deep to fill the space?
Which tile adhesive should I use for 60x60cm porcelain floor tiles? The floor is concrete that has an area that has been self levelled & there is a small section that has floorboards. I was thinking to use a flexible adhesive? Also which size trowel would be better for this large of a tile?
So, I've tiled most of the wall in my downstairs WC and am left with a narrow floor to ceiling strip at each end of about 25mm (see pic)
The majority of this gap will have the flat section of the tile trim so what should I use to stick the tile strips with?
I'm assuming the standard tile...
I am planning to get 1000x1000 tiles in my kitchen from the following website. In the quote they have also suggested the following tile adhesive and grouting.
Larsen Standard Set Flexible Plus Grey Floor & Wall Tile Adhesive S1 Grade...
need eyes in the back of your head.
Using Norcros NX standard set floor tile adhesive. After an issue with multipro boards I did some trials with this product. Following tec instructions on the bag, to the letter, after. 4 day cure my tiles pulled off with minimal finger pressure.
On primed ext...
ive got a plastic (i think its acrylic) shower tray. Its not one of the heavy stone resin type.
Anyway im going to lay it on a bed of flexible tile adhesive and wanted to check, when laying the adhesive out on the floor do you guys comb it out using the notched side of the trowel or just lay a...
Need some help please with calculating levels and the build up of the floor to support tiling.
Not sure about the need for the uncoupling mat?
Not sure about the thickness of the tile adhesive?
As I have sliding glass doors to be spec'ed and installed before the screed, I need to gauge the...
Hi I’m fitting a Nova Frameless 1000 x 800 Sliding Door Shower Enclosure with a low profile shower tray that you lay on sand and cement. I’ve fitted Some aqua boards and where I’m fitting the enclosure the walls are slight out of plum by about 10-15mm.
I’ve already primed the walls with Mapei...
Hi all,
Just after a bit of advice please. I had my kitchen floor tiled last week (porcelain tiles).
I think there is movement and cracking/crumbling grout in some of the tiles. I supplied the tiles and the grout. The tiler supplied everything else including the adhesive. I think he’s used the...
Which tile adhesive have you most used during 2021?
Reply with the make, and upvote if you've used that one also.
We'll see who gets the most upvotes. And I'll mark that adhesive make the winner.
I wont be disallowing new members from getting involved, unlike previous years, so just...
I am about to try tiling a splashback, having only tiled once before (10+ years ago)
I've watched a few YT videos so think I know what to do, but there are so many brands of adhesive available, from well-known names to own brand names.
I'll be using 200 x 100 ceramic tiles and think ready...
Hi all,
Got some 1sqm 6mm tiles to lay and the subfloor is 18mm T&G ply on top of joists. On this is 6mm hardie board (was used to build up height to match landing) and ditra mat.
Underneath this is wet UFH.
As the ply is straight onto joists the floor is not exactly 100% flat and level. It's...
This was mentioned in another thread, so I thought I'd ask the question to others to get a feel for it.
Larsen rep "blamed everything but their products and said their report was final".
Anybody has any larsen tile adhesive fails recently? Perhaps a bad batch they're not pulling?
I had an issue recently that I've never seen before and any help or advice would be greatly appreciated. I used a Larsen acrylic primer on gyspum walls as instructed on product (walls had been skimmed 8+ weeks previous and moisture tested prior to sealing and tiling). 18 months later and it...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.